Новые поступления

Naze32 CC3D SP Racing F3 LED Strip Alarm LED WS2812B RGB For QAV250 RC Drone 4pcs lot naze32 cc3d sp racing f3 led strip ws2812b rgb for qav250 rc drone can control max 32 leds with one pins with alarm
Naze32 CC3D SP Racing F3 LED Strip Alarm LED WS2812B RGB For RC Drone Can set the color and fucntion of LED Strip with cleanflight configurator GUI: Description: Working Voltage: 5V Suitable for the flight controller that support cleanflight, such as NazeNaze32, CC3D, skyline32 and SP Racing F3 etc. Can control max 32 LEDs with one pins Each LED can display different colors at same time, mutual independence. Functions: Indicate the pitch/roll positon of transmitter Indicate the nose and direction Indicate the flight mode and status Low voltage alarm, failure safety alarm Alarm: Arm-lock enable: Green LED light/off flash, when calibrate the flight controller or in large inclination Low Battery: Red LED flah, when the voltage is lower then the setting Failsafe: Blue and Yellow LEDs flash, when the sign between receiver and remote control transmitter is disconnected. Connecting: CC3D: RCO5, Data in Naze32: RC5, Data in Suggest: You can order 4 sets LED for your drone. Install them on the bottom of arms. Use 2 LEDs in same color on nose of drone for indication, 2 sets LEDs on tail for alarm. When it is fail, it can notice the player in time. Package Included: 1 x Shrinkable Tube 1 x Strip Light 3 x 20cm Silicon Cable
2.59 RUR
Diatone WS2812 WS2812B RGB LED Board 5050 For Naze32 CC3D 4pcs lot naze32 cc3d sp racing f3 led strip ws2812b rgb for qav250 rc drone can control max 32 leds with one pins with alarm
Diatone WS2812 WS2812B RGB LED Board 5050 For Naze32 CC3D Description: Make your own little LED strip arrangement with this stick of WS2812B LEDs. We crammed 8 of the tiny 5050 (5mm x 5mm) smart RGB LEDs onto a PCB with mounting holes and a chainable design. Use only one microcontroller pin to control as many as you can chain together. Each LED is addressable as the driver chip is inside the LED. Each one has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and no external choke resistors are required making the design slim. Power the whole thing with 5VDC (4-7V works) and you're ready to rock. The LEDs are "chainable" by connecting the output of one stick into the input of another. There is a single data line with a very timing-specific protocol. Since the protocol is very sensitive to timing, it requires a real-time microconroller such as an AVR, Arduino, PIC, mbed, etc. It cannot be used with a Linux-based microcomputer or interpreted microcontroller such as the netduino or Basic Stamp. An 8MHz or faster processor is required. Comes as a single stick with 8 individually addressable RGB LEDs assembled and tested. Features: WS2812B, the second generation of the build-in IC, is 5050RGB LED with 4 soldering points. Compared with WS2812 with 6 soldering points, it keeps your wiring arrangement neater. Can be used with Naze32, CC3D, showing the situation of FC lock/unlock, aileron, brake, throttle, alarm functions, etc. Size: 51mm*10mm Applications: Naze32 LED Strip with CleanFlight AVR, Arduino, PIC, mbed, etc Package included: 1 x LED BOARD & 1 x 0.3m cable
2.99 RUR
PDB Power Distribution Board 5V/12V BEC with LED for SP Racing F3 NAZE32 CC3D Flight Controller 4pcs lot naze32 cc3d sp racing f3 led strip ws2812b rgb for qav250 rc drone can control max 32 leds with one pins with alarm
PDB Power Distribution Board 5V/12V BEC with LED for SP Racing F3 NAZE32 CC3D Flight Controller Specification: Item name:Power Distribution Board BEC: 5V/12V output Compatibled with QVA250, ZMR250 frame kit Support CC3D, NAZE32, SP Racing F3 flight controller Package Included: 1 X Power Distribution Board
12.99 RUR
Upgrade NAZE32 SP Racing F3 Flight Control Acro 6 DOF/Deluxe 10 DOF for Multicopter 4pcs lot naze32 cc3d sp racing f3 led strip ws2812b rgb for qav250 rc drone can control max 32 leds with one pins with alarm
Upgrade NAZE32 SP Racing F3 Flight Control 6 DOF/10 DOF for Multicopter Specification: Item Name: SP Racing F3 Flight Control NAZE32 Upgrade Version for Multicopter Acro Deluxe Version Version: Acro 6DOFand Deluxe 10DOF (with MS5611 Barometer and HMC5883 Compass) *35x35mm board, 30mm mounting holes. * STM32F3 CPU. * High-capacity Flash (Acro 6DOF and Deluxe 10DOF) * MPU6050 Accelerometers and Gyroscopes * MS5611 Barometer (Deluxe 10DOF) * HMC5883 Compass (Deluxe 10DOF) * MicroUSB socket. * 4 x 4 pin JST-SH Socket (I2C, SWD, 2xuart) * 2 x 8 pin JST-SH Socket (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND) * 8 x 3 pin though-holes for pin headers for ESC / Servo connections. * 2 x 4 pin though-holes for the 2x serial ports . * 2 x 2 pin though-holes for battery voltage and buzzer. Features: Better coding practices and introducing tests, easier to maintain and for future development. (Dominic has software development background) Many bugs fixed from Baseflight. Supports more flight controllers, including CC3D, CJMCU and Sparky. Supports OneShot ESC and more than 8 RC channels. Additional PID controllers that uses floating point arithmetic operations. (now has 3 built-in PID Controllers) Many more features such as RGB LED strip support, Autotune, In-flight PID tuning with your radio, blackbox flight data logging etc. Flight Performance The SPR F3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it's on rails. No-Compromise I/O Use all the features all the time; e.g. Connect your OSD + SmartPort + SBus + GPS + LED Strip + Battery Monitoring + Sonar + 8 motors - all at the same time. Configurable The SP F3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux). Tiny and lightweight The RacingF3 has a standard 35x35mm form-factor with 30mm mounting holes and weighs just 6 grams. Flight Logging On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork. Next-Generation CPU The RacingF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor (FPU) for efficient flight calculations that gets more done in less time. Loop times up to ~2x as fast as previous-generation STM32F1 based boards. Developer Friendly Developer friendly debugging port (SWD) and boot mode selection, unbrickable bootloader. OneShot ESC Full support for OneShot ESCs for easy PID tuning and a sharper response. Broad RC receiver Support Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in). Programmable LED Dedicated output for programmable LEDs - great for orientation, racing and night flying. Battery Monitoring Battery monitoring ports for voltage and current. Sonar Sonar support for precision low-altitude hold. I2C Port I2C port always powered, perfect for external sensors or always-on OLED Screen. Buzzer Buzzer port for audible warnings and notification Package Included: Acro 6DOF Version 1 x Upgrade NAZE32 SP Racing F3 Flight Control for Multicopter 2 x 8p Wire Rod 2 x 4p Extension Path 5 x Pins set Deluxe 10DOF Version 1 x Upgrade NAZAE32 SP Racing F3 Flight Control for Multicopter with MS5611 Barometer and HMC5883 Compass 2 x 8p Wire Rod 2 x 4p Extension Path 5 x Pins set
22.99 RUR